Share
This guide explains how to complete the Lorex Setup Wizard on X Series 8-Channel, 16-Channel, and 32-Channel NVRs. Follow the on-screen instructions to activate the recorder, create your administrator password, configure network and time settings, connect cameras, prepare a hard drive for recording, and set up the Lorex Connect app.
TABLE OF CONTENTS
- Before Starting the Setup Wizard
- Steps 1–5: Activate and Secure the NVR
- Steps 6–10: Configure Network, Date, and Time
- Step 11: Add and Review Cameras
- Step 12: Check and Format the Hard Drive
- Step 13: Set Up the Lorex Connect App
- Step 14: Set Display Resolution and Finish
- Pair the Recorder with Lorex Connect
- Helpful Setup Tips
Before Starting the Setup Wizard
The Setup Wizard opens when you turn on a new or factory-reset NVR. Use the connected USB mouse to select options and enter information on each screen.
- Connect the monitor: Connect the NVR to a monitor or TV using HDMI or VGA. Set the monitor to the matching input.
- Connect the USB mouse: Plug the mouse into the KB/MOUSE USB port on the front of the recorder.
- Connect the network: Use an Ethernet cable to connect your router to the NVR's WAN port. An external PoE switch connected directly to the NVR uses the LAN port.
- Connect cameras: Connect compatible cameras to the NVR's built-in PoE ports or through a supported router/PoE switch arrangement. Cameras connected through a router or an external switch may need to be added during camera setup.
- Power on the NVR: Connect the included power cable, turn on the rear power switch, and follow the prompts on the monitor.
Steps 1–5: Activate and Secure the NVR
Step 1: Welcome
The Welcome screen introduces the recorder setup. Connecting the NVR to a router allows remote viewing and online firmware updates.
- Review the welcome message.
- Click Start.
Step 2: Activation — Create Your Administrator Password
On the Activation screen, choose the system language and create the password you will use to sign in to the NVR.
- Select your preferred Language.
- In the administrator password field, enter a strong password that meets the requirements shown on the screen.
- Enter the same password again in the confirmation field.
- Click OK to continue.
Step 3: Pattern Unlock (Optional)
Pattern Unlock lets you sign in locally by drawing a pattern on the recorder screen instead of typing your password each time.
- Draw a pattern across the circles on the screen.
- Draw the same pattern again to confirm it.
- If you do not want to use Pattern Unlock, click Skip this step.
Step 4: Password Recovery — Set Security Questions
Security questions provide a way to recover access if you forget your NVR administrator password.
- Choose or review the three security questions displayed on the screen.
- Enter an answer for each question.
- Click OK to save the answers. The screen also offers Skip this step, but completing the questions is strongly recommended.
- Keep your answers in a secure location so you can use them later if needed.
Step 5: Cloud Update
When the NVR is connected to a router and the Internet, it checks for available firmware updates during setup.
- Allow the recorder to check for the latest firmware.
- If an update is available, follow the on-screen process and allow the update to finish.
- Do not disconnect power or turn off the NVR during a firmware update.
- Continue when the recorder advances to the next setup screen.
Steps 6–10: Configure Network, Date, and Time
Step 6: Open the Setup Wizard
After activation, the recorder displays the Setup Wizard screen.
- Click Setup Wizard to begin the system configuration screens.
Step 7: Network Settings
The Network screen displays the recorder's network configuration, including DHCP, IP address, DNS and port mapping.
- Confirm the router is connected to the NVR's WAN port.
- Review DHCP. When enabled, the router can automatically assign the recorder an IP address and other network settings.
- If your network uses a manually assigned address, enter the appropriate IP address, gateway and DNS information provided for your network.
- Review the available network and port mapping settings. Leave them at their current values unless your network requires different settings.
- Click Next.
Step 8: Date and Time
Correct date and time settings help ensure recordings and detected events display the right timestamps.
- Select the Date Format and Time Format you prefer.
- Review the NTP (Network Time Protocol) setting. When enabled and the recorder has network access, the NVR can synchronize time with an NTP server.
- Review the NTP server and synchronization settings shown on the screen.
- Check the displayed date and time, and correct them if needed.
- Click Next.
Step 9: Time Zone
- Open the Time Zone drop-down list.
- Select the time zone for the location where the NVR is installed.
- Click Next.
Step 10: Daylight Saving Time (DST)
Use this screen to set daylight saving time for your location.
- Turn DST on or off depending on whether daylight saving time applies where the recorder is installed.
- If DST is enabled, review the Start Time, End Time and Offset Time settings.
- Click Next.
Step 11: Add and Review Cameras
The Camera screen lists camera channels and their connection status. Compatible cameras connected directly to the NVR's built-in PoE ports are automatically detected and added. Cameras connected through your local network using a router or external PoE switch can be found through a search or added manually.
For cameras connected to built-in PoE ports
- Check that each camera's Ethernet cable is securely connected to a built-in PoE port on the NVR.
- Allow approximately 30–60 seconds for the camera to power on and initialize.
- Review the connected cameras in the channel list.
For cameras connected through a router or external PoE switch
- Confirm that the cameras are powered and that the NVR and camera network connections are in place.
- Click Start Search to scan for available cameras on the network.
- Select the camera from the results, enter its password when prompted, then click Add.
- If a camera is not listed, click + Add to enter its IP address, protocol, port, username and password manually.
- Use Modify to update an existing camera's connection settings, or Delete to remove a camera from a channel.
- Review the connected cameras, then click Next to continue.
Step 12: Check and Format the Hard Drive
The Disk screen lists the hard drives installed in the NVR and their status. A new hard drive must be formatted before it can be used for local video recording.
- Review the drive list and identify the HDD you want to use for recording.
- If the installed HDD is new or has not been formatted for the NVR, select that drive.
- Click Format and follow the on-screen confirmation.
- When formatting is finished, confirm the disk is available for recording.
- Click Next.
Step 13: Set Up the Lorex Connect App
Lorex Connect allows you to access the recorder from a compatible mobile device.
- On your phone, open the App Store or Google Play and download the Lorex Connect app.
- Open the app and create an account or log in.
- Tap + Add device, then select Recorder.
- On the NVR Setup Wizard, review the Lorex Connect app information and click Next.
For the full connection and pairing procedure, continue to Pair the Recorder with Lorex Connect below.
Step 14: Set Display Resolution and Finish
The final screen controls the video resolution sent from the NVR to your connected monitor or TV.
- Open Output Resolution and choose a setting supported by your monitor or TV.
- If you do not want the wizard to appear again automatically, select Don't show setup wizard next time.
- Click Finish.
- The NVR opens Live View, where you can see video from connected cameras.
Pair the Recorder with Lorex Connect
After completing the NVR Setup Wizard, finish linking the recorder to the Lorex Connect app for remote viewing.
- Install the app: Download Lorex Connect from the App Store or Google Play.
- Sign in: Open the app, then tap Create an account or Log in.
- Add the recorder: Tap + Add device and select Recorder.
- If your phone and NVR are on the same network: Follow the in-app prompts to find and add the recorder.
- If your phone and NVR are on different networks: Tap My recorder is on a different network than my Lorex Connect app at the bottom of the app screen.
- Open the recorder's pairing screen: On the NVR, go to Main Menu > Settings > System > Lorex Connect App.
- Scan the QR code: Use the Lorex Connect app to scan the QR code shown on the recorder.
- Name your system: After pairing succeeds, enter a name for the recorder and finish the app setup.
Helpful Setup Tips
- Keep your NVR password: Save the password you created during Activation and the answers to your security questions in a secure place.
- Check camera status: Cameras connected directly to built-in PoE ports are detected automatically; network-connected cameras can be located using Start Search or added with + Add.
- New HDDs need formatting: Even if the NVR powers on and cameras display in Live View, local recording needs an installed, formatted HDD.
- Set your time correctly: Confirm the time zone, NTP and DST settings so your recording timestamps are accurate.
- Use the WAN port for the router: On X Series NVRs with separate LAN and WAN ports, the router connects to the WAN port.
- Finish the app pairing: Downloading Lorex Connect is only the first step; add and pair the recorder to access it through the app.


























































































































































































































































