The SL301 Series - 2K Wi-Fi Smart Lightbulb Pan-Tilt Camera can be installed with any standard E26 light socket.
For additional support, check out the Lorex Connect App Guide, the Troubleshooting Guide or the Frequently Asked Questions (FAQs).
TABLE OF CONTENTS
- How to Install Video
- What's Included
- 2K Wi-Fi Smart Lightbulb Pan-Tilt Camera
- Safety Information
- Install the Lightbulb Camera
- Add the Lightbulb Camera to the App
- Status LED Light
- Certification
How to Install Video
Watch for step-by-step guidance.
What's Included
- 2K Wi-Fi Smart Lightbulb Pan-Tilt Camera
Safety Information
WARNING: RISK OF ELECTRIC SHOCK – USE IN DRY LOCATION
NOT FOR USE IN TOTALLY ENCLOSED LUMINAIRES
DO NOT USE WITH DIMMERS
AVERTISSEMENT: RISQUE DE CHOC ÉLECTRIQUE – POUR UTILISATION DANS UN ENDROIT SEC
NE CONVIENT PAS À DES LUMINAIRES TOTALEMENT FERMÉS
NE PAS UTILISER AVEC UN GRADATEUR
This device is not intended for use with emergency exits.
Cet appareil n’est pas conçu pour être utilisé avec des sorties de secours.
Disconnect power before installing or removing operation.
Déconnectez l'alimentation avant d'installer ou de retirer l'opération.
NOT FOR USE IN TOTALLY ENCLOSED LUMINAIRES
DO NOT USE WITH DIMMERS
AVERTISSEMENT: RISQUE DE CHOC ÉLECTRIQUE – POUR UTILISATION DANS UN ENDROIT SEC
NE CONVIENT PAS À DES LUMINAIRES TOTALEMENT FERMÉS
NE PAS UTILISER AVEC UN GRADATEUR
This device is not intended for use with emergency exits.
Cet appareil n’est pas conçu pour être utilisé avec des sorties de secours.
Disconnect power before installing or removing operation.
Déconnectez l'alimentation avant d'installer ou de retirer l'opération.
EN:
- Never disassemble the device.
- Secure the device firmly to prevent falls or injury.
- Keep out of reach of children.
- Operate only within specified temperature and humidity ranges.
- Clean with a dry cloth only.
- Not suitable for emergency lighting.
- Do not use in enclosed fixtures.
- Control brightness and dimming through the app.
- Ne démontez jamais l’appareil.
- Fixez solidement l’appareil pour éviter les chutes ou les blessures.
- Gardez hors de portée des enfants.
- Utilisez seulement dans les plages de température et d’humidité spécifiées.
- Nettoyez uniquement avec un chiffon sec.
- Non adapté à l’éclairage de secours.
- Ne pas utiliser dans des luminaires fermés.
- Contrôlez la luminosité et l’intensité à l’aide de l’application.
Install the Lightbulb Camera
- Turn off the light.
- Screw the lightbulb camera into an E26 light socket.
Do not turn on the light until you have downloaded and logged into the app.
Note: The lightbulb cannot be replaced.
Add the Lightbulb Camera to the App
To add the lightbulb camera:
Note: The screenshots in this guide are for illustration purposes only. The look of the Lorex Connect app may vary slightly depending on your device, app version, or operating system.
Download the Lorex Connect app from the App Store or Google Play.
Open the app and log in or create an account.
Tap Add device and select 2K lightbulb camera.
Power on the lightbulb camera, then tap Next in the app.
- Tap the lightbulb camera when it is detected in the app. Tap Add this device.
- Select your Wi-Fi network in the app and enter the password.The lightbulb camera connects to dual-band Wi-Fi networks; 2.4 GHz & 5 GHz.
- Name your lightbulb camera and tap Continue.
- Allow any updates to install. Do not power off the device. Once the update is complete, your device will reboot.
- To register your device for warranty, visit www.lorex.com/warranty.
Status LED Light
The Status LED, located next to the camera lens, displays the current state of your smart lightbulb camera, such as power status, network connectivity, or readiness to pair with the app.
| Blinking Slowly | The lightbulb camera is on but not yet set up. Open the Lorex Connect app to start setup. |
| Blinking Slowly (during setup) | The lightbulb camera is trying to connect to Wi-Fi or the Lorex Cloud. Stay close to your router during setup. |
| Blinking Quickly | The lightbulb camera is connected to Wi-Fi, but there's no internet access. Check your router or modem. |
| Solid Green | Everything is working! The lightbulb camera is online and ready to use. (You can turn off the Status LED light in the Lorex Connect app if you want). |
| Fading (resetting) | The lightbulb camera is being reset to factory settings. Keep it powered on until the process finishes. |
| Fading (updating) | The lightbulb camera is installing a firmware update. Don't unplug or turn it off until the update is complete. |
Certification
Models: SL301A-46W-AZ1, SL301A-46W-AA1
FCC & IC:
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with a minimum distance of 20 cm between the radiator and body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage; (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Radio Frequency Exposure Statement for IC
This equipment complies with IC exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure conditions. This equipment shall be installed and operated with a minimum distance of 20 cm between the radiator and body.
Cet équipement est conforme aux limites d’exposition IC établies pour un environnement non contrôlé. L’appareil peut être utilisé dans des conditions d’exposition portables. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et le corps.