X Series 8-CH - HDD Installation, Replacement & Formatting

Modified on November 19, 2026

Back to Newsroom

This guide explains how to remove an existing hard drive (HDD), install a new or replacement hard drive, and format the HDD in an X Series – Lorex Connect XC 4K 8-Channel NVR.

Applicable models:

  • RNE01P-82B-AB1: Model with a pre-installed HDD.
  • RNE01P-8ZB-AB1: Model without a pre-installed HDD.
Where should I start? If you are replacing an existing HDD, begin with Step 1: Remove the Existing Hard Drive. If your NVR was sold without an HDD or the drive bay is empty, go directly to Step 2: Install the New Hard Drive. After installing a new drive, complete Step 3: Format the Hard Drive.

TABLE OF CONTENTS


Before You Begin

The 8-Channel X Series NVR supports one internal 3.5-inch SATA hard drive, up to 12 TB. Choose a compatible surveillance-grade HDD designed for continuous recording. This model has one HDD bay, unlike the 16- and 32-channel NVRs.

What you will need:

  • One compatible surveillance-grade 3.5-inch SATA HDD (12 TB maximum).
  • A Phillips screwdriver for the recorder's cover and HDD mounting screws.
  • The proper HDD mounting screws. The 8-channel NVR package includes HDD screws; retain screws from an existing drive when replacing it.
  • A monitor and USB mouse to access the recorder's Disk menu after installation.
CAUTION: Turn off the NVR and disconnect its power adapter from the power source before opening the recorder or handling the drive. Disconnect the other cables as well. Never install or remove an HDD while the recorder is powered on.
Important: Formatting permanently erases all data on the selected HDD. Back up any recordings you need before replacing or formatting a drive.

Step 1: Remove the Existing Hard Drive

Follow these instructions only if a drive is already installed and you are replacing or removing it. If the recorder has an empty drive bay, skip to Step 2.

  1. Power off and disconnect the recorder. Shut down the NVR, unplug the power adapter from the power source, and disconnect the other cables. Place the NVR on a stable, flat work surface.
  2. Remove the top-cover screws. Use a Phillips screwdriver to remove four side screws (two on each side) and one rear screw. Keep them in a safe place for reassembly.

    side cover screw positions

    rear cover screw positions

  3. Open the NVR case. Slide the top cover away from the NVR, then carefully lift it off to expose the HDD.

    Sliding and lifting the top cover

  4. Support the HDD and turn the NVR over. Hold the installed drive securely in place with one hand while carefully flipping the NVR to access the bottom panel.

    Supporting the HDD while flipping the NVR

  5. Remove the four HDD mounting screws. With the bottom panel accessible, remove the four screws securing the HDD to the chassis. Continue supporting the HDD to prevent it from shifting.

    Four bottom-panel HDD screws

  6. Turn the NVR upright. Keep a hand on the loosened HDD, carefully turn the NVR upright again, and slide the HDD partway out to expose its connectors.

    HDD partially pulled out after turning the recorder upright

  7. Disconnect the HDD cables. Gently unplug both the SATA data cable and the HDD power cable by pulling the connectors straight out rather than tugging the wires.

    Disconnecting SATA data and power cables

  8. Remove the existing HDD. Carefully remove the drive from the NVR. The empty bay is now ready for a replacement.

Continue to Step 2: Install the New Hard Drive.


Step 2: Install the New Hard Drive

Follow these steps to install a new HDD or replace an existing drive. If your RNE01P-8ZB-AB1 was sold without a drive, begin here after opening the powered-off, disconnected recorder using the cover-removal instructions in Step 1.

Installing your first HDD? The recorder must be powered off and unplugged before you open the case or install the drive.
  1. Prepare the new hard drive. Confirm that it is a compatible 3.5-inch SATA HDD with a capacity of 12 TB or less.
  2. Insert the HDD. Slide the new drive into the NVR's single HDD bay and hold it securely with one hand.

    Sliding HDD into the drive bay

  3. Connect the drive cables. Plug the NVR's SATA data cable and HDD power cable into the corresponding connectors on the new drive. Make sure the connectors are fully seated.

    Attaching the SATA and HDD power connectors to the new drive

    SATA and HDD power connectors attached to the new drive

  4. Turn the NVR over while supporting the HDD. Carefully flip the recorder to expose its bottom panel. Keep the HDD in place with one hand.

    Turning recorder over while holding HDD

  5. Align the drive mounting holes. Match the screw holes on the bottom of the drive with the corresponding holes on the bottom of the NVR chassis.
  6. Secure the HDD. Use a Phillips screwdriver to install and tighten the four HDD mounting screws through the bottom panel.

    Installing four bottom-panel HDD mounting screws

  7. Turn the NVR upright and replace its cover. Carefully flip the unit upright, slide the top cover back into place, and reinstall the cover screws in their original positions.

    rear cover screw positions

    side cover screw positions

    rear cover screw positions

  8. Reconnect and power on the recorder. Reconnect the monitor, mouse, network and camera cables as needed. Reconnect the power adapter, then turn on the NVR.
  9. Format the installed HDD. The new drive must be formatted before the recorder can use it for local recording. Continue to Step 3: Format the Hard Drive.

Step 3: Format the Hard Drive

Formatting prepares the newly installed HDD to store local recordings on the X Series NVR.

Warning: Formatting permanently deletes all existing data on the selected hard drive. Confirm you are formatting the intended drive and have backed up any recordings you want to keep.
  1. From Live View, right-click twice to open the Main Menu.
  2. Click Settings.
  3. Select the Record tab at the top of the menu.
  4. Click Disk from the left-side menu.
  5. Select the Disk tab.
  6. Select the installed HDD, if it is not already selected.
  7. Click Format and confirm the formatting prompt.

Settings > Record > Disk > Disk page, showing Format

After formatting finishes, check the hard drive status in the next section.


Step 4: Check the Hard Drive Status and Recording Overwrite

In the same Settings > Record > Disk > Disk menu, confirm the new drive is recognized and review its recording settings.

  1. Locate the installed drive in the Disk list.
  2. Check Disk Status. During normal operation, it should display Normal.
  3. Review the available details, including the drive's Disk SN and Used Space.
  4. If applicable, review the Disk Group assignment.
  5. Enable Recording Overwrite if you want the NVR to automatically replace the oldest recordings when the HDD becomes full. If overwrite is disabled, recording stops once the drive is full.
  6. If needed, configure Expired Time (Day) to control recording retention.
  7. Click Apply to save any changes.

Disk settings with Disk Status, Disk SN, Used Space, Recording Overwrite and Expired Time (Day)

Tip: Enable Recording Overwrite to keep recording when the HDD reaches capacity. The NVR will automatically overwrite the oldest recordings. Remember that the 8-channel NVR has one internal HDD bay.

Helpful Tips

  • No HDD included? For RNE01P-8ZB-AB1, begin with Step 2: Install the New Hard Drive. First follow the cover-opening instructions in Step 1, but skip removing an existing drive.
  • HDD capacity: Use a compatible 3.5-inch SATA drive, up to 12 TB.
  • Drive not listed? Power off and unplug the recorder before checking that the SATA data and power cables are connected securely.
  • Drive not recording? Confirm the disk has been formatted and shows Normal status. Review the recorder's recording schedule.
  • Continuous recording storage: Enable Recording Overwrite if you want the NVR to continue saving video when the disk fills.
  • More details: See Chapter 11 – Recording & Storage, especially Sections 11.2.1–11.2.3, of the X Series XC 8-Channel NVR User Manual (SKU: RNE01P-8).

Leave a comment

Please note, comments need to be approved before they are published.